Aluminium profiles

Perforated aluminium corner

Perforated Aluminium corner used to hedge the corners of walls made of plasterboard. It ensures quick and esthetic finish of the edge. Corner occurs in different thicknesses, depending on the application and needed strength: thickness of 0.3 mm with a wing 19x19, 0.35 mm thickness with a wing 23x23 mm and a thickness of 0.35 mm with a wing 25x25 mm.

We recommend the last one because of its strength and stability.

Montege

Place profile in the desired location, which previously has been coated with a suitable putty, after pressing the corner it should get out through the holes drilled in the profile. Then we align putty flush evenly with the edge of the corner and leave to dry.

Technical specification:
thickness	od 0,3 do 0,35 mm
length	250 cm i 300 cm
package	200 pieces

Perforated aluminum corner – obtuse angle 135

Obtuse angle corner used when connecting plasterboard to protect against cracking and to obtain straightness.

Montage

Place profile in the desired location, which previously has been coated with a suitable putty, after pressing the corner it should get out through the holes drilled in the profile. Then we align putty flush evenly with the edge of the corner and leave to dry.

Technical specification:
length	250 cm i 300 cm
package	50 pieces

Aluminum corner for gips plaster, - NTG

Corner is made of aluminum sheet. It is used to finish and protect the corners of the walls during carrying out wet plaster. Especially recommended for use in environments with high humidity and acidity (eg. Gypsum plaster).

Technical specification:
types	NTM AL lub NTG (fine mesh)
width	34x34
length	250 i 300 cm

Aluminum corner with mesh

Aluminum corner with a fiberglass mesh, used in thermal insulation systems to reinforce the corners of buildings, allows for a smooth and straight finishing of the polystyrene edge . Corner occurs in different thicknesses and with different mesh widths, depending on the use and needs strength: thickness of 0.3 mm with a wing 19x19, 0.35 mm thickness with a wing 23x23 mm. We recommend the latter because of its strength and stability.

Montage

Place profile in the desired location, which previously has been coated with a suitable glue. After pressed against on the profile, glue should infiltrate out through the bores and the mesh. Then we align glue flush to the edge of the corner and leave to dry.

Technical specification:
types	NAL7x7; NAL8x8 ; NAL 10x10
length	250 cm i 300 cm
package	6 x 25 pieces

Aluminum half-corner – ALP

Perforated Aluminium hlf-corner used to hedge the corners of walls made of plasterboard. The useage of this profile ensures the finishing straight line and solid protection from mechanical damage.

Montege

Place profile in the desired location, which previously has been coated with a suitable putty, after pressing the corner it should get out through the holes drilled in the profile. Then we align putty flush evenly with the edge of the corner and leave to dry.

Technical specification:
length	250 cm i 300 cm
package	200 pieces

Socle profile

Aluminium socle profiles used in insulation board panels to protect the system from impacts on the lowest parts of it. Aluminum based, thickness 0,6 mm.

Montage

Place profile in the desired location, which previously has been coated with a suitable putty, after pressing the corner it should get out through the holes drilled in the profile. Then we align putty flush evenly with the edge of the corner and leave to dry.

Technical specification:
length	250 cm
width	3, 4, 5, 8, 10, 12, 15, 16, 18, 20, 25 cm
package	20 pieces

Call us , we advise:

Helpline +48 77 547 19 55

Our company

We produce and supply the highest quality construction materials throughout the Poland and the European Union. We produce fiberglass mesh, decorative wall coverings and profiles according to any specification.

We offer

fiberglass mesh
wall coverings fiberglass
construction profiles made of aluminum, steel and PVC

Address:

Fiberglass Fabrics s.c.
ul. Torowa 4
45-073 Opole
Poland